KONTRONIK Downloads
ProgUNIT
JIVE Pro
Program Update
-
Update JIVE Pro 80+ HV (Version 1.10)
460KB -
Update JIVE Pro 120+ HV (Version 1.10)
460KB
With the version 1.10 the TelMe JETI und MIKADO can be used.
-
Update JIVE Pro 80+ HV (Version 1.9)
430KB -
Update JIVE Pro 120+ HV (Version 1.9)
430KB
With the version 1.9 TelMe Futaba FX 22, T18MZ, T18MZ-WC and T14SG can be used.
-
Update JIVE Pro 80+ HV (Version 1.8)
372KB -
Update JIVE Pro 120+ HV (Version 1.8)
372KB
Version 1.8 includes funcionality for TelMe Futaba
-
Update JIVE Pro 80+ HV (Version 1.6)
414KB -
Update JIVE Pro 120+ HV (Version 1.6)
414KB
Version 1.6 allows to adjust the value for the alarm parameter of TelMe module. Also the automatic commutation was optimized to reduce high current peaks on some special motors. It’s necessary to update the K-Konfig program and the ProgDISC as well.
-
Update JIVE Pro 80+ HV (Version 1.4)
190KB -
Update JIVE Pro 120+ HV (Version 1.4)
190KB
With version 1.4 will be problems solved which occur during Initialisation at temperatures lower than (≤ 5-6° C / 41-43° F).
KOSMIK
Program Update
-
Update KOSMIK 160(Version 4.10)
460KB -
Update KOSMIK 200(Version 4.10)
460KB
With this version 4.10 the TelMe JETI und MIKADO can be used.
-
Update KOSMIK 160(Version 4.9)
429KB -
Update KOSMIK 200(Version 4.9)
430KB
With the version 4.9 TelMe Futaba FX 22, T18MZ, T18MZ-WC and T14SG can be used. In addition the software enables the use of HV-LiPos with an end-of-charge voltage up to 4.35 V.
-
Update KOSMIK 160(Version 4.8)
372KB -
Update KOSMIK 200(Version 4.8)
371KB
Version 4.8 includes funcionality for TelMe Futaba.
-
Update KOSMIK 160(Version 4.6)
414KB -
Update KOSMIK 200(Version 4.6)
414KB
Version 4.6 has several changes. With the actual K-Konfig program it’s possible to adjust the alarm values for Telme.
An alarm is now also logged in the error file. The startup time after bailout has been optimized corresponding to the programmed startup time.
With long startup times its much faster now to guarantee save startup after bailout. Der calculation of the used capacity was corrected.
It’s necessary to update the K-Konfig program and the ProgDISC as well.
-
Update KOSMIK 160(Version 4.5)
361KB -
Update KOSMIK 200(Version 4.5)
361KB
Document
-
Manual for Mode 10
150KB
With the new Mode 10 the BEC voltage can be adjusted by the Tx and does not need a progrmming unit.
PROGDISC
Program Update
-
Version 1.11
414KB
With this update the PROGDISC is optimized for the latest generation of our KOBY series. -
Version 1.10
414KB
This version is necessary for a successful update of your KOSMIK to Version 4.6 or higher or JIVE Pro Version 1.6 or higher. -
Version 1.9
130KB
This version is highly recommended for a successful update of your KOSMIK to Version 4.2
One thought on “Kontronik”